Merge commit '20b787fc1284176834cbe7ca2134e4b36bec5828'
[tmk_keyboard.git] / converter / x68k_usb / Makefile
1 #
2 # Makefile for PJRC Teensy
3 #
4
5
6 # Target file name (without extension).
7 TARGET = x68k_usb
8
9 # Directory common source filess exist
10 TMK_DIR = ../../tmk_core
11
12 # Directory keyboard dependent files exist
13 TARGET_DIR = .
14
15 # keyboard dependent files
16 SRC = keymap.c \
17 matrix.c \
18 led.c \
19 protocol/serial_uart.c
20
21 CONFIG_H = config.h
22
23
24 # MCU name, you MUST set this to match the board you are using
25 # type "make clean" after changing this, so all files will be rebuilt
26 #MCU = at90usb162 # Teensy 1.0
27 #MCU = atmega32u4 # Teensy 2.0
28 #MCU = at90usb646 # Teensy++ 1.0
29 #MCU = at90usb1286 # Teensy++ 2.0
30 MCU = atmega32u2 # Teensy 2.0
31
32
33 # Processor frequency.
34 # Normally the first thing your program should do is set the clock prescaler,
35 # so your program will run at the correct speed. You should also set this
36 # variable to same clock speed. The _delay_ms() macro uses this, and many
37 # examples use this variable to calculate timings. Do not add a "UL" here.
38 F_CPU = 16000000
39
40
41 #
42 # LUFA specific
43 #
44 # Target architecture (see library "Board Types" documentation).
45 ARCH = AVR8
46
47 # Input clock frequency.
48 # This will define a symbol, F_USB, in all source code files equal to the
49 # input clock frequency (before any prescaling is performed) in Hz. This value may
50 # differ from F_CPU if prescaling is used on the latter, and is required as the
51 # raw input clock is fed directly to the PLL sections of the AVR for high speed
52 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
53 # at the end, this will be done automatically to create a 32-bit value in your
54 # source code.
55 #
56 # If no clock division is performed on the input clock inside the AVR (via the
57 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
58 F_USB = $(F_CPU)
59
60 # Interrupt driven control endpoint task(+60)
61 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
62
63
64 # Boot Section Size in bytes
65 # Teensy halfKay 512
66 # Atmel DFU loader 4096
67 # LUFA bootloader 4096
68 OPT_DEFS += -DBOOTLOADER_SIZE=4096
69
70
71 # Build Options
72 # *Comment out* to disable the options.
73 #
74 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
75 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
76 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
77 CONSOLE_ENABLE = yes # Console for debug(+400)
78 COMMAND_ENABLE = yes # Commands for debug and configuration
79 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
80 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
81
82
83
84 #---------------- Programming Options --------------------------
85 AVRDUDE = avrdude
86 # Type: avrdude -c ? to get a full listing.
87 AVRDUDE_PROGRAMMER = avr109
88 AVRDUDE_PORT = /dev/ttyACM0
89 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
90 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
91
92 # Uncomment the following if you want avrdude's erase cycle counter.
93 # Note that this counter needs to be initialized first using -Yn,
94 # see avrdude manual.
95 #AVRDUDE_ERASE_COUNTER = -y
96
97 # Uncomment the following if you do /not/ wish a verification to be
98 # performed after programming the device.
99 #AVRDUDE_NO_VERIFY = -V
100
101 # Increase verbosity level. Please use this when submitting bug
102 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
103 # to submit bug reports.
104 #AVRDUDE_VERBOSE = -v -v
105
106 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
107 #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
108 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
109 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
110 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
111
112 PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
113
114
115 # Search Path
116 VPATH += $(TARGET_DIR)
117 VPATH += $(TMK_DIR)
118
119
120 include $(TMK_DIR)/protocol.mk
121 include $(TMK_DIR)/protocol/lufa.mk
122 include $(TMK_DIR)/common.mk
123 include $(TMK_DIR)/rules.mk
Imprint / Impressum