converter/x68k_usb/Makefile

   1 #
   2 # Makefile for PJRC Teensy
   3 #
   4
   5
   6 # Target file name (without extension).
   7 TARGET = x68k_usb_pjrc
   8
   9 # Directory common source filess exist
  10 TOP_DIR = ../..
  11
  12 # Directory keyboard dependent files exist
  13 TARGET_DIR = .
  14
  15 # keyboard dependent files
  16 SRC =   keymap.c \
  17         matrix.c \
  18         led.c \
  19         protocol/x68k.c
  20 #       protocol/serial_uart.c
  21
  22 CONFIG_H = config_pjrc.h
  23
  24
  25 # MCU name, you MUST set this to match the board you are using
  26 # type "make clean" after changing this, so all files will be rebuilt
  27 #MCU = at90usb162       # Teensy 1.0
  28 MCU = atmega32u4       # Teensy 2.0
  29 #MCU = at90usb646       # Teensy++ 1.0
  30 #MCU = at90usb1286      # Teensy++ 2.0
  31
  32
  33 # Processor frequency.
  34 #   Normally the first thing your program should do is set the clock prescaler,
  35 #   so your program will run at the correct speed.  You should also set this
  36 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  37 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  38 F_CPU = 16000000
  39
  40
  41 # Boot Section Size in bytes
  42 #   Teensy halfKay   512
  43 #   Atmel DFU loader 4096
  44 #   LUFA bootloader  4096
  45 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  46
  47
  48 # Build Options
  49 #   *Comment out* to disable the options.
  50 #
  51 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
  52 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  53 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  54 CONSOLE_ENABLE = yes    # Console for debug(+400)
  55 COMMAND_ENABLE = yes    # Commands for debug and configuration
  56 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  57 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  58
  59
  60
  61 #---------------- Programming Options --------------------------
  62 AVRDUDE = avrdude
  63 # Type: avrdude -c ? to get a full listing.
  64 AVRDUDE_PROGRAMMER = avr109
  65 AVRDUDE_PORT = /dev/ttyACM0
  66 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
  67 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
  68
  69 # Uncomment the following if you want avrdude's erase cycle counter.
  70 # Note that this counter needs to be initialized first using -Yn,
  71 # see avrdude manual.
  72 #AVRDUDE_ERASE_COUNTER = -y
  73
  74 # Uncomment the following if you do /not/ wish a verification to be
  75 # performed after programming the device.
  76 #AVRDUDE_NO_VERIFY = -V
  77
  78 # Increase verbosity level.  Please use this when submitting bug
  79 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
  80 # to submit bug reports.
  81 #AVRDUDE_VERBOSE = -v -v
  82
  83 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
  84 #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
  85 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
  86 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
  87 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
  88
  89 #PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
  90 #PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
  91 PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
  92
  93
  94 # Search Path
  95 VPATH += $(TARGET_DIR)
  96 VPATH += $(TOP_DIR)
  97
  98
  99 include $(TOP_DIR)/protocol/pjrc.mk
 100 include $(TOP_DIR)/protocol.mk
 101 include $(TOP_DIR)/common.mk
 102 include $(TOP_DIR)/rules.mk