]>
git.gir.st - tmk_keyboard.git/blob - keyboard/hhkb/Makefile
1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
44 # Directory common source filess exist
45 TMK_DIR ?
= ..
/..
/tmk_core
47 # Directory keyboard dependent files exist
51 # List C source files here. (C dependencies are automatically generated.)
61 # TMK Alt Controller or PJRC Teensy 2.0
64 # Processor frequency.
65 # This will define a symbol, F_CPU, in all source code files equal to the
66 # processor frequency in Hz. You can then use this symbol in your source code to
67 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
68 # automatically to create a 32-bit value in your source code.
70 # This will be an integer division of F_USB below, as it is sourced by
71 # F_USB after it has run through any CPU prescalers. Note that this value
72 # does not *change* the processor frequency - it should merely be updated to
73 # reflect the processor speed set externally so that the code can use accurate
81 # Target architecture (see library "Board Types" documentation).
84 # Input clock frequency.
85 # This will define a symbol, F_USB, in all source code files equal to the
86 # input clock frequency (before any prescaling is performed) in Hz. This value may
87 # differ from F_CPU if prescaling is used on the latter, and is required as the
88 # raw input clock is fed directly to the PLL sections of the AVR for high speed
89 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
90 # at the end, this will be done automatically to create a 32-bit value in your
93 # If no clock division is performed on the input clock inside the AVR (via the
94 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
97 # Interrupt driven control endpoint task
98 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
101 # Boot Section Size in *bytes*
103 # Teensy++ halfKay 1024
104 # Atmel DFU loader 4096 (TMK Alt Controller)
105 # LUFA bootloader 4096
107 OPT_DEFS
+= -DBOOTLOADER_SIZE
=4096
111 # comment out to disable the options.
113 BOOTMAGIC_ENABLE
= yes
# Virtual DIP switch configuration
114 MOUSEKEY_ENABLE
= yes
# Mouse keys
115 EXTRAKEY_ENABLE
= yes
# Audio control and System control
116 CONSOLE_ENABLE
= yes
# Console for debug
117 COMMAND_ENABLE
= yes
# Commands for debug and configuration
118 NKRO_ENABLE
= yes
# USB Nkey Rollover
119 #KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
120 #HHKB_JP = yes # HHKB JP support
122 #ACTIONMAP_ENABLE = yes # Use 16bit actionmap instead of 8bit keymap
123 #KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
125 #OPT_DEFS += -DNO_ACTION_TAPPING
126 #OPT_DEFS += -DNO_ACTION_LAYER
127 #OPT_DEFS += -DNO_ACTION_MACRO
136 ifdef ACTIONMAP_ENABLE
137 KEYMAP_FILE
= actionmap
143 SRC
:= $(KEYMAP_FILE
)_
$(KEYMAP
).c
$(SRC
)
146 SRC
:= $(KEYMAP_FILE
)_jp.c
$(SRC
)
148 SRC
:= $(KEYMAP_FILE
)_hhkb.c
$(SRC
)
153 ifneq (, $(or
$(findstring keymap_jp.c
, $(SRC
)), $(findstring yes
, $(HHKB_JP
))))
154 OPT_DEFS
+= -DHHKB_JP
159 VPATH
+= $(TARGET_DIR
)
162 include $(TMK_DIR
)/protocol
/lufa.mk
163 include $(TMK_DIR
)/common.mk
164 include $(TMK_DIR
)/rules.mk
166 debug-on
: EXTRAFLAGS
+= -DDEBUG
-DDEBUG_ACTION
169 debug-off
: EXTRAFLAGS
+= -DNO_DEBUG
-DNO_PRINT
170 debug-off
: OPT_DEFS
:= $(filter-out -DCONSOLE_ENABLE
,$(OPT_DEFS
))