protocol/usb_hid/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 TARGET = usbkbd
  43
  44 # Directory keyboard dependent files exist
  45 TARGET_DIR = .
  46
  47 # MCU name
  48 MCU = atmega32u4
  49
  50
  51 # Processor frequency.
  52 #     This will define a symbol, F_CPU, in all source code files equal to the
  53 #     processor frequency in Hz. You can then use this symbol in your source code to
  54 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  55 #     automatically to create a 32-bit value in your source code.
  56 #
  57 #     This will be an integer division of F_USB below, as it is sourced by
  58 #     F_USB after it has run through any CPU prescalers. Note that this value
  59 #     does not *change* the processor frequency - it should merely be updated to
  60 #     reflect the processor speed set externally so that the code can use accurate
  61 #     software delays.
  62 F_CPU = 16000000
  63
  64
  65
  66
  67 ARDUINO_DIR = arduino-1.0.1/cores
  68 ARDUINO_SRC = \
  69         arduino/Print.cpp \
  70         arduino/Stream.cpp \
  71         arduino/wiring.c
  72
  73 #       arduino/main.cpp \
  74 #       arduino/USBCore.cpp \
  75 #       arduino/CDC.cpp \
  76 #       arduino/HID.cpp \
  77 #       arduino/HardwareSerial.cpp \
  78 #       arduino/IPAddress.cpp \
  79 #       arduino/Tone.cpp \
  80 #       arduino/WMath.cpp \
  81 #       arduino/WInterrupts.c \
  82 #       arduino/wiring_analog.c \
  83 #       arduino/wiring_pulse.c \
  84 #       arduino/wiring_shift.c
  85 #       arduino/wiring_digital.c \
  86 #       arduino/WString.cpp \
  87 #       arduino/new.cpp \
  88
  89 USB_HOST_DIR = ./USB_Host_Shield_2.0
  90 USB_HOST_SRC = \
  91         Usb.cpp \
  92         cdcacm.cpp \
  93         cdcftdi.cpp \
  94         cdcprolific.cpp \
  95         hid.cpp \
  96         hidboot.cpp \
  97         hiduniversal.cpp \
  98         hidusagetitlearrays.cpp \
  99         hidescriptorparser.cpp \
 100         message.cpp \
 101         parsetools.cpp
 102
 103         #PS3BT.cpp \
 104         #PS3USB.cpp \
 105         #RFCOMM.cpp \
 106         #XBOXUSB.cpp \
 107         #adk.cpp \
 108         #masstorage.cpp \
 109         #max_LCD.cpp \
 110         #usbhub.cpp
 111
 112 #SRC =  host_kbd.cpp
 113 SRC =  main.cpp
 114 SRC +=  parser.cpp
 115 SRC +=  NullSerial.cpp
 116 SRC += $(USB_HOST_SRC)
 117 SRC += $(ARDUINO_SRC)
 118
 119 OPT_DEFS = -DARDUINO=101 -DUSB_VID=0x2341 -DUSB_PID=0x8036
 120
 121 # Search Path
 122 VPATH += $(TARGET_DIR)
 123 VPATH += $(USB_HOST_DIR)
 124 VPATH += $(ARDUINO_DIR)
 125 # for Arduino.h
 126 VPATH += arduino-1.0.1/cores/arduino
 127 # for pins_arduino.h
 128 VPATH += arduino-1.0.1/variants/leonardo
 129
 130
 131 # Ad hoc workaround to override original arduino/USBAPI.h with our own USBAPI.h.
 132 # Obsolete but needed in order to remove directory including the current input file from search list.
 133 # Option -iquote can't replace -I- for this purpose.
 134 EXTRAFLAGS += -I-
 135
 136
 137 # program Leonardo
 138 PROGRAM_CMD = avrdude -patmega32u4 -cavr109 -P$(DEV) -b57600 -Uflash:w:$(TARGET).hex
 139
 140
 141 include ../../rules.mk