Makefile.macway

   1 # Hey Emacs, this is a -*- makefile -*-
   2 #----------------------------------------------------------------------------
   3 # WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
   4 #
   5 # Released to the Public Domain
   6 #
   7 # Additional material for this makefile was written by:
   8 # Peter Fleury
   9 # Tim Henigan
  10 # Colin O'Flynn
  11 # Reiner Patommel
  12 # Markus Pfaff
  13 # Sander Pool
  14 # Frederik Rouleau
  15 # Carlos Lamas
  16 #
  17 #----------------------------------------------------------------------------
  18 # On command line:
  19 #
  20 # make all = Make software.
  21 #
  22 # make clean = Clean out built project files.
  23 #
  24 # make coff = Convert ELF to AVR COFF.
  25 #
  26 # make extcoff = Convert ELF to AVR Extended COFF.
  27 #
  28 # make program = Download the hex file to the device, using avrdude.
  29 #                Please customize the avrdude settings below first!
  30 #
  31 # make debug = Start either simulavr or avarice as specified for debugging,
  32 #              with avr-gdb or avr-insight as the front end for debugging.
  33 #
  34 # make filename.s = Just compile filename.c into the assembler code only.
  35 #
  36 # make filename.i = Create a preprocessed source file for use in submitting
  37 #                   bug reports to the GCC project.
  38 #
  39 # To rebuild project do "make clean" then "make all".
  40 #----------------------------------------------------------------------------
  41
  42
  43 # Target file name (without extension).
  44 TARGET = tmk
  45
  46
  47 # List C source files here. (C dependencies are automatically generated.)
  48 SRC =   $(TARGET).c \
  49         usb.c \
  50         usb_keyboard.c \
  51         usb_mouse.c \
  52         usb_debug.c \
  53         keymap.c \
  54         matrix.c \
  55         jump_bootloader.c \
  56         print.c
  57
  58
  59 # MCU name, you MUST set this to match the board you are using
  60 # type "make clean" after changing this, so all files will be rebuilt
  61 #MCU = at90usb162       # Teensy 1.0
  62 MCU = atmega32u4        # Teensy 2.0
  63 #MCU = at90usb646       # Teensy++ 1.0
  64 #MCU = at90usb1286      # Teensy++ 2.0
  65
  66
  67 # Processor frequency.
  68 #   Normally the first thing your program should do is set the clock prescaler,
  69 #   so your program will run at the correct speed.  You should also set this
  70 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  71 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  72 F_CPU = 16000000
  73
  74
  75 # Output format. (can be srec, ihex, binary)
  76 FORMAT = ihex
  77
  78
  79 # Object files directory
  80 #     To put object files in current directory, use a dot (.), do NOT make
  81 #     this an empty or blank macro!
  82 OBJDIR = .
  83
  84
  85 # List C++ source files here. (C dependencies are automatically generated.)
  86 CPPSRC =
  87
  88
  89 # List Assembler source files here.
  90 #     Make them always end in a capital .S.  Files ending in a lowercase .s
  91 #     will not be considered source files but generated files (assembler
  92 #     output from the compiler), and will be deleted upon "make clean"!
  93 #     Even though the DOS/Win* filesystem matches both .s and .S the same,
  94 #     it will preserve the spelling of the filenames, and gcc itself does
  95 #     care about how the name is spelled on its command-line.
  96 ASRC =
  97
  98
  99 # Optimization level, can be [0, 1, 2, 3, s].
 100 #     0 = turn off optimization. s = optimize for size.
 101 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
 102 OPT = s
 103
 104
 105 # Debugging format.
 106 #     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
 107 #     AVR Studio 4.10 requires dwarf-2.
 108 #     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
 109 DEBUG = dwarf-2
 110
 111
 112 # List any extra directories to look for include files here.
 113 #     Each directory must be seperated by a space.
 114 #     Use forward slashes for directory separators.
 115 #     For a directory that has spaces, enclose it in quotes.
 116 EXTRAINCDIRS =
 117
 118
 119 # Compiler flag to set the C Standard level.
 120 #     c89   = "ANSI" C
 121 #     gnu89 = c89 plus GCC extensions
 122 #     c99   = ISO C99 standard (not yet fully implemented)
 123 #     gnu99 = c99 plus GCC extensions
 124 CSTANDARD = -std=gnu99
 125
 126
 127 # Place -D or -U options here for C sources
 128 CDEFS = -DF_CPU=$(F_CPU)UL
 129
 130
 131 # Place -D or -U options here for ASM sources
 132 ADEFS = -DF_CPU=$(F_CPU)
 133
 134
 135 # Place -D or -U options here for C++ sources
 136 CPPDEFS = -DF_CPU=$(F_CPU)UL
 137 #CPPDEFS += -D__STDC_LIMIT_MACROS
 138 #CPPDEFS += -D__STDC_CONSTANT_MACROS
 139
 140
 141
 142 #---------------- Compiler Options C ----------------
 143 #  -g*:          generate debugging information
 144 #  -O*:          optimization level
 145 #  -f...:        tuning, see GCC manual and avr-libc documentation
 146 #  -Wall...:     warning level
 147 #  -Wa,...:      tell GCC to pass this to the assembler.
 148 #    -adhlns...: create assembler listing
 149 CFLAGS = -g$(DEBUG)
 150 CFLAGS += $(CDEFS)
 151 CFLAGS += -O$(OPT)
 152 CFLAGS += -funsigned-char
 153 CFLAGS += -funsigned-bitfields
 154 CFLAGS += -ffunction-sections
 155 CFLAGS += -fpack-struct
 156 CFLAGS += -fshort-enums
 157 CFLAGS += -Wall
 158 CFLAGS += -Wstrict-prototypes
 159 #CFLAGS += -mshort-calls
 160 #CFLAGS += -fno-unit-at-a-time
 161 #CFLAGS += -Wundef
 162 #CFLAGS += -Wunreachable-code
 163 #CFLAGS += -Wsign-compare
 164 CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 165 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 166 CFLAGS += $(CSTANDARD)
 167
 168
 169 #---------------- Compiler Options C++ ----------------
 170 #  -g*:          generate debugging information
 171 #  -O*:          optimization level
 172 #  -f...:        tuning, see GCC manual and avr-libc documentation
 173 #  -Wall...:     warning level
 174 #  -Wa,...:      tell GCC to pass this to the assembler.
 175 #    -adhlns...: create assembler listing
 176 CPPFLAGS = -g$(DEBUG)
 177 CPPFLAGS += $(CPPDEFS)
 178 CPPFLAGS += -O$(OPT)
 179 CPPFLAGS += -funsigned-char
 180 CPPFLAGS += -funsigned-bitfields
 181 CPPFLAGS += -fpack-struct
 182 CPPFLAGS += -fshort-enums
 183 CPPFLAGS += -fno-exceptions
 184 CPPFLAGS += -Wall
 185 CPPFLAGS += -Wundef
 186 #CPPFLAGS += -mshort-calls
 187 #CPPFLAGS += -fno-unit-at-a-time
 188 #CPPFLAGS += -Wstrict-prototypes
 189 #CPPFLAGS += -Wunreachable-code
 190 #CPPFLAGS += -Wsign-compare
 191 CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 192 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 193 #CPPFLAGS += $(CSTANDARD)
 194
 195
 196 #---------------- Assembler Options ----------------
 197 #  -Wa,...:   tell GCC to pass this to the assembler.
 198 #  -adhlns:   create listing
 199 #  -gstabs:   have the assembler create line number information; note that
 200 #             for use in COFF files, additional information about filenames
 201 #             and function names needs to be present in the assembler source
 202 #             files -- see avr-libc docs [FIXME: not yet described there]
 203 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 204 #       dump that will be displayed for a given single line of source input.
 205 ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 206
 207
 208 #---------------- Library Options ----------------
 209 # Minimalistic printf version
 210 PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
 211
 212 # Floating point printf version (requires MATH_LIB = -lm below)
 213 PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
 214
 215 # If this is left blank, then it will use the Standard printf version.
 216 PRINTF_LIB =
 217 #PRINTF_LIB = $(PRINTF_LIB_MIN)
 218 #PRINTF_LIB = $(PRINTF_LIB_FLOAT)
 219
 220
 221 # Minimalistic scanf version
 222 SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
 223
 224 # Floating point + %[ scanf version (requires MATH_LIB = -lm below)
 225 SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
 226
 227 # If this is left blank, then it will use the Standard scanf version.
 228 SCANF_LIB =
 229 #SCANF_LIB = $(SCANF_LIB_MIN)
 230 #SCANF_LIB = $(SCANF_LIB_FLOAT)
 231
 232
 233 MATH_LIB = -lm
 234
 235
 236 # List any extra directories to look for libraries here.
 237 #     Each directory must be seperated by a space.
 238 #     Use forward slashes for directory separators.
 239 #     For a directory that has spaces, enclose it in quotes.
 240 EXTRALIBDIRS =
 241
 242
 243
 244 #---------------- External Memory Options ----------------
 245
 246 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 247 # used for variables (.data/.bss) and heap (malloc()).
 248 #EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
 249
 250 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 251 # only used for heap (malloc()).
 252 #EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
 253
 254 EXTMEMOPTS =
 255
 256
 257
 258 #---------------- Linker Options ----------------
 259 #  -Wl,...:     tell GCC to pass this to linker.
 260 #    -Map:      create map file
 261 #    --cref:    add cross reference to  map file
 262 LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
 263 LDFLAGS += -Wl,--relax
 264 LDFLAGS += -Wl,--gc-sections
 265 LDFLAGS += $(EXTMEMOPTS)
 266 LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
 267 LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
 268 #LDFLAGS += -T linker_script.x
 269
 270
 271
 272 #---------------- Programming Options (avrdude) ----------------
 273
 274 # Programming hardware
 275 # Type: avrdude -c ?
 276 # to get a full listing.
 277 #
 278 AVRDUDE_PROGRAMMER = stk500v2
 279
 280 # com1 = serial port. Use lpt1 to connect to parallel port.
 281 AVRDUDE_PORT = com1    # programmer connected to serial device
 282
 283 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
 284 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
 285
 286
 287 # Uncomment the following if you want avrdude's erase cycle counter.
 288 # Note that this counter needs to be initialized first using -Yn,
 289 # see avrdude manual.
 290 #AVRDUDE_ERASE_COUNTER = -y
 291
 292 # Uncomment the following if you do /not/ wish a verification to be
 293 # performed after programming the device.
 294 #AVRDUDE_NO_VERIFY = -V
 295
 296 # Increase verbosity level.  Please use this when submitting bug
 297 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
 298 # to submit bug reports.
 299 #AVRDUDE_VERBOSE = -v -v
 300
 301 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
 302 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
 303 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
 304 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 305
 306
 307
 308 #---------------- Debugging Options ----------------
 309
 310 # For simulavr only - target MCU frequency.
 311 DEBUG_MFREQ = $(F_CPU)
 312
 313 # Set the DEBUG_UI to either gdb or insight.
 314 # DEBUG_UI = gdb
 315 DEBUG_UI = insight
 316
 317 # Set the debugging back-end to either avarice, simulavr.
 318 DEBUG_BACKEND = avarice
 319 #DEBUG_BACKEND = simulavr
 320
 321 # GDB Init Filename.
 322 GDBINIT_FILE = __avr_gdbinit
 323
 324 # When using avarice settings for the JTAG
 325 JTAG_DEV = /dev/com1
 326
 327 # Debugging port used to communicate between GDB / avarice / simulavr.
 328 DEBUG_PORT = 4242
 329
 330 # Debugging host used to communicate between GDB / avarice / simulavr, normally
 331 #     just set to localhost unless doing some sort of crazy debugging when
 332 #     avarice is running on a different computer.
 333 DEBUG_HOST = localhost
 334
 335
 336
 337 #============================================================================
 338
 339
 340 # Define programs and commands.
 341 SHELL = sh
 342 CC = avr-gcc
 343 OBJCOPY = avr-objcopy
 344 OBJDUMP = avr-objdump
 345 SIZE = avr-size
 346 AR = avr-ar rcs
 347 NM = avr-nm
 348 AVRDUDE = avrdude
 349 REMOVE = rm -f
 350 REMOVEDIR = rm -rf
 351 COPY = cp
 352 WINSHELL = cmd
 353
 354
 355 # Define Messages
 356 # English
 357 MSG_ERRORS_NONE = Errors: none
 358 MSG_BEGIN = -------- begin --------
 359 MSG_END = --------  end  --------
 360 MSG_SIZE_BEFORE = Size before:
 361 MSG_SIZE_AFTER = Size after:
 362 MSG_COFF = Converting to AVR COFF:
 363 MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
 364 MSG_FLASH = Creating load file for Flash:
 365 MSG_EEPROM = Creating load file for EEPROM:
 366 MSG_EXTENDED_LISTING = Creating Extended Listing:
 367 MSG_SYMBOL_TABLE = Creating Symbol Table:
 368 MSG_LINKING = Linking:
 369 MSG_COMPILING = Compiling C:
 370 MSG_COMPILING_CPP = Compiling C++:
 371 MSG_ASSEMBLING = Assembling:
 372 MSG_CLEANING = Cleaning project:
 373 MSG_CREATING_LIBRARY = Creating library:
 374
 375
 376
 377
 378 # Define all object files.
 379 OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 380
 381 # Define all listing files.
 382 LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 383
 384
 385 # Compiler flags to generate dependency files.
 386 GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
 387
 388
 389 # Combine all necessary flags and optional flags.
 390 # Add target processor to flags.
 391 ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
 392 ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
 393 ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
 394
 395
 396
 397
 398
 399 # Default target.
 400 all: begin gccversion sizebefore build sizeafter end
 401
 402 # Change the build target to build a HEX file or a library.
 403 build: elf hex eep lss sym
 404 #build: lib
 405
 406
 407 elf: $(TARGET).elf
 408 hex: $(TARGET).hex
 409 eep: $(TARGET).eep
 410 lss: $(TARGET).lss
 411 sym: $(TARGET).sym
 412 LIBNAME=lib$(TARGET).a
 413 lib: $(LIBNAME)
 414
 415
 416
 417 # Eye candy.
 418 # AVR Studio 3.x does not check make's exit code but relies on
 419 # the following magic strings to be generated by the compile job.
 420 begin:
 421         @echo
 422         @echo $(MSG_BEGIN)
 423
 424 end:
 425         @echo $(MSG_END)
 426         @echo
 427
 428
 429 # Display size of file.
 430 HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
 431 #ELFSIZE = $(SIZE) --mcu=$(MCU) --format=avr $(TARGET).elf
 432 ELFSIZE = $(SIZE) $(TARGET).elf
 433
 434 sizebefore:
 435         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
 436         2>/dev/null; echo; fi
 437
 438 sizeafter:
 439         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
 440         2>/dev/null; echo; fi
 441
 442
 443
 444 # Display compiler version information.
 445 gccversion :
 446         @$(CC) --version
 447
 448
 449
 450 # Program the device.
 451 program: $(TARGET).hex $(TARGET).eep
 452         $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
 453
 454
 455 # Generate avr-gdb config/init file which does the following:
 456 #     define the reset signal, load the target file, connect to target, and set
 457 #     a breakpoint at main().
 458 gdb-config:
 459         @$(REMOVE) $(GDBINIT_FILE)
 460         @echo define reset >> $(GDBINIT_FILE)
 461         @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
 462         @echo end >> $(GDBINIT_FILE)
 463         @echo file $(TARGET).elf >> $(GDBINIT_FILE)
 464         @echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
 465 ifeq ($(DEBUG_BACKEND),simulavr)
 466         @echo load  >> $(GDBINIT_FILE)
 467 endif
 468         @echo break main >> $(GDBINIT_FILE)
 469
 470 debug: gdb-config $(TARGET).elf
 471 ifeq ($(DEBUG_BACKEND), avarice)
 472         @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
 473         @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
 474         $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
 475         @$(WINSHELL) /c pause
 476
 477 else
 478         @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
 479         $(DEBUG_MFREQ) --port $(DEBUG_PORT)
 480 endif
 481         @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
 482
 483
 484
 485
 486 # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
 487 COFFCONVERT = $(OBJCOPY) --debugging
 488 COFFCONVERT += --change-section-address .data-0x800000
 489 COFFCONVERT += --change-section-address .bss-0x800000
 490 COFFCONVERT += --change-section-address .noinit-0x800000
 491 COFFCONVERT += --change-section-address .eeprom-0x810000
 492
 493
 494
 495 coff: $(TARGET).elf
 496         @echo
 497         @echo $(MSG_COFF) $(TARGET).cof
 498         $(COFFCONVERT) -O coff-avr $< $(TARGET).cof
 499
 500
 501 extcoff: $(TARGET).elf
 502         @echo
 503         @echo $(MSG_EXTENDED_COFF) $(TARGET).cof
 504         $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
 505
 506
 507
 508 # Create final output files (.hex, .eep) from ELF output file.
 509 %.hex: %.elf
 510         @echo
 511         @echo $(MSG_FLASH) $@
 512         $(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock -R .signature $< $@
 513
 514 %.eep: %.elf
 515         @echo
 516         @echo $(MSG_EEPROM) $@
 517         -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
 518         --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
 519
 520 # Create extended listing file from ELF output file.
 521 %.lss: %.elf
 522         @echo
 523         @echo $(MSG_EXTENDED_LISTING) $@
 524         $(OBJDUMP) -h -S -z $< > $@
 525
 526 # Create a symbol table from ELF output file.
 527 %.sym: %.elf
 528         @echo
 529         @echo $(MSG_SYMBOL_TABLE) $@
 530         $(NM) -n $< > $@
 531
 532
 533
 534 # Create library from object files.
 535 .SECONDARY : $(TARGET).a
 536 .PRECIOUS : $(OBJ)
 537 %.a: $(OBJ)
 538         @echo
 539         @echo $(MSG_CREATING_LIBRARY) $@
 540         $(AR) $@ $(OBJ)
 541
 542
 543 # Link: create ELF output file from object files.
 544 .SECONDARY : $(TARGET).elf
 545 .PRECIOUS : $(OBJ)
 546 %.elf: $(OBJ)
 547         @echo
 548         @echo $(MSG_LINKING) $@
 549         $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
 550
 551
 552 # Compile: create object files from C source files.
 553 $(OBJDIR)/%.o : %.c
 554         @echo
 555         @echo $(MSG_COMPILING) $<
 556         $(CC) -c $(ALL_CFLAGS) $< -o $@
 557
 558
 559 # Compile: create object files from C++ source files.
 560 $(OBJDIR)/%.o : %.cpp
 561         @echo
 562         @echo $(MSG_COMPILING_CPP) $<
 563         $(CC) -c $(ALL_CPPFLAGS) $< -o $@
 564
 565
 566 # Compile: create assembler files from C source files.
 567 %.s : %.c
 568         $(CC) -S $(ALL_CFLAGS) $< -o $@
 569
 570
 571 # Compile: create assembler files from C++ source files.
 572 %.s : %.cpp
 573         $(CC) -S $(ALL_CPPFLAGS) $< -o $@
 574
 575
 576 # Assemble: create object files from assembler source files.
 577 $(OBJDIR)/%.o : %.S
 578         @echo
 579         @echo $(MSG_ASSEMBLING) $<
 580         $(CC) -c $(ALL_ASFLAGS) $< -o $@
 581
 582
 583 # Create preprocessed source for use in sending a bug report.
 584 %.i : %.c
 585         $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
 586
 587
 588 # Target: clean project.
 589 clean: begin clean_list end
 590
 591 clean_list :
 592         @echo
 593         @echo $(MSG_CLEANING)
 594         $(REMOVE) $(TARGET).hex
 595         $(REMOVE) $(TARGET).eep
 596         $(REMOVE) $(TARGET).cof
 597         $(REMOVE) $(TARGET).elf
 598         $(REMOVE) $(TARGET).map
 599         $(REMOVE) $(TARGET).sym
 600         $(REMOVE) $(TARGET).lss
 601         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
 602         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
 603         $(REMOVE) $(SRC:.c=.s)
 604         $(REMOVE) $(SRC:.c=.d)
 605         $(REMOVE) $(SRC:.c=.i)
 606         $(REMOVEDIR) .dep
 607
 608
 609 # Create object files directory
 610 $(shell mkdir $(OBJDIR) 2>/dev/null)
 611
 612
 613 # Include the dependency files.
 614 -include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
 615
 616
 617 # Listing of phony targets.
 618 .PHONY : all begin finish end sizebefore sizeafter gccversion \
 619 build elf hex eep lss sym coff extcoff \
 620 clean clean_list program debug gdb-config